It might be small, but the link400.4mini is in a class by itself. It is small enough to fit just about anywhere, but it really punches above its weight. The link400.4mini is perfect for powering front and rear speakers. When used in 3-channel mode, the amplifier can produce 100 watts x 2 for the main speakers and 200 watts x 1 for a subwoofer, so it won’t lack for power. Speaking of the subwoofer, channels 3/4 have a 1-band PEQ, a subsonic filter and the ability to add an RLC to fine tune the subwoofers performance.
The link400.4mini has our adaptive loading technology plus the ability to handle up to 40V of hi-level input. It also has fully adjustable high and low pass crossovers, with 1x/10x switch so you can do active component speakers. For factory audio systems where no full-range signal is present, the link400.4mini has built-in summing, so it can handle that internally, without the need for an outboard processor. Like all Wāvtech amplifiers, the link400.4mini is start/stop system and EV compatible out of the box.
Output Power
- 65 watts x 4 @ 4 ohms
- 100 watts x 4 @ 2 ohms
- 200 watts x 2 @ 4 ohms BTL
Features
- Small Footprint Only 7.2”x4.5”x1.65”
- Variable Hi/Low Pass Crossover (-12dB/oct)
- Variable Subsonic Filter (-12dB/oct)
- Built-In Summing w/Level Trim Adjustment
- Start/Stop System Compatible (stable down to 7 volts)
- Differential Balanced Inputs
- Variable Gain Adjustment w/Clip LED
- Auto Turn-On via DC-Offset or Audio Signal Detect
- OEM Load Detect Compatible
- Locking Detachable Hi-Level Speaker Terminals
- Professional Grade Panel Mount RCA’s
- Compact Aluminium Chassis w/Detachable Mounting tabs
-
Amplifier switches/dials located on the top panel:
INPUT CH - These switches are for selecting which input channels feed the respective channels. For 2-channel sources, connect the source to CH1/2's RCA or speaker level inputs and set CH3/4's input select to copy (1/2). For 4-channel sources, set CH1/2 to direct (1/2) and CH3/4 to direct (3/4). : For a 3-channel system from a factory 2-way source, CH1/2 would be set to sum (1+3/2+4) for full-range output to the main speakers, while CH3/4 would be set to direct (3/4) to pass only the factory woofer signal to drive the subwoofer.
INPUT RANGE - Choose the input range that will accommodate the source's maximum output signal voltage without excessive clipping, 5V or 10V for low level (RCA) inputs, and 20V or 40V for speaker level inputs.
GAIN - Each channel pair has a variable gain with corresponding clipping indicator, where the clip LED will dimly illuminate just before the onset of clipping and become fully bright when the amplifier has reached full power output at clipping. When summing, these gain adjustments should be used for matching relative levels so that the combined signals sum as close to flat as possible or to the desired frequency response. Note that CH3/4's gain adjustment will be bypassed if its input select switch is set to copy (1/2).
FILTER - This switch selects the filter mode as either a high-pass (HP) or low-pass (LP) crossover, and is bypassed when set to OFF (default).
FREQ - When either the HP or LP filter mode is activated, this variable adjustment sets the filter's cut-off frequency (F3) from 50Hz to 500Hz with a slope of -12dB/oct.
LEVEL TRIM - When summing, and after setting gains and crossovers for appropriate frequency response, these adjustments allow the power output of CH1/2 and CH3/4 to be increased or decreased independently by up to +/-6dB for final volume balance between them while preserving the summing ratio established by the gains.